Electronics Forum / Repair / February 2006

The dishwasher just stopped in the middle of normal wash cycle and the
indicator on normal cycle butter flashed all the time. I pushed
reset/start button and the dishwasher won't run and the indicator on
normal cycle butter flashed again. Before calling the service man, I

19" NEC computer monitor model:JC-19W40,chassis:Z85A,year:July
2000,unknown anufacturer's model:FE950(A),Mitsubishi crt.I could not
find an FCC ID code,UL or CSA file no.
No horizontal deflection (only straight line going top to bottom,I

First, I did search the group and did not find the specific info I
need.  I was given an older Maytag 1/3 hp 1725 rpm washing machine
motor and need help with the wiring to retask it for other use.
The wiring block on the end of the motor is set up with six connectors,

This is an electronic question, it is related to a security panel and the
End Of Line Resistor.  For those that do not know the EOLR is a resistor
that in placed within the protected loop to provide a small amount of
current to flow and thus supervises the loop.  If the loop is ...

I have a GE TV model 13GP241 with a TX826TB chassis
The problem I am having is when the set powers up, after 2 or 3 seconds
it starts cycling on & off continiously.
I have no schematics for this set & its not really a cost effective

This washer worked fine today, however I had the idea it took a rather long
dry spin cycle. During my second laundry load it took the water, but the
machine failed to spin, it cycled the rinse periods Ok but it never turned
the drum.

I just got a Canon UCS5. video output is B&W on both composite and
S-video. Any hints or a source for schematics/service manual?
Thanks.
doug

Does anyone have an old Tektronix scope similar to this?  I just got it
from a surplus dump where it has been sitting in an unheated shed for a
few years.  The tubes light up, and it gets a spot on the screen, but
the trace doesn't move at all, no matter what the settings are.  I ...

HOW TO MAKE QUICK EASY MONEY!!!!? : TURN $6 INTO THOUSANDS!!!!!!!!
   : READING THIS COULD CHANGE YOUR LIFE! IT DOES WORK!

while back, I was browsing through newsgroups, just like you are now, :

I've got a defective FQPF5N60 Power MOSFET which I need to replace. The part
seems to be available in bulks only (here in Europe).
Does anybody know of a replacement?
Kind regards, Leo

TV will not power on. First disconnected red HV to splitter and tried
to power on. No luck. Next checked HOT for short, none found. Checked
voltage at collector of hot. Voltage shot up to 220 volts and then
trickled down to zero. The set does make a chirp sound when first

I have sound but no picture because I have no HV. I have no HV because
I have no B+. I measured for B+ with collector of HOT disconnected but
found none. No fuses or bad parts found - except for C523 1uf/160v.
All other caps check ok. This set uses STR S5708 for regulation. Is it

Fuser failed on this cheap laser printer. Being a "fix it rather than add to
the land fill" kinda' guy, I'm exploring if it's possible.
I've priced the new fuser assembly, and it's nearing the price of a new
printer (surprise!), so that possibility is ruled out immediately.

Hi, I just bought this tek and while it passes all the selftests,
it's really flaky at startup.
When you press the on/stby button the lights blink once , you can hear some
relays switching and it goes dead.

Does anyone know of a source for exact replacement USB jacks for this
laptop? The spring contacts are badly worn or sprung. I see that Allied
has a listing from Keystone in which they look similar from the outside
view. Any thoughts or sources? Thanks, Jeff