General - Repair

Thread preview

Thread	Last Post	Replies

VTVM	18 Mar 2005 03:29 GMT	6
I purchased a Olson VTVM at a sale recently for 50 cents--always wanted one as a young teen. I have several digital VOM's-- Question: Any practical value of a VTVM on my tool bench over a digital VOM?
Sony & horizontal line	18 Mar 2005 02:18 GMT	1
I have a KV-C292 Sony TV (chassis AE-1C) which is recently showing a lighter horizontal line in the middle of the screen. I’ve found R530 open. I’ve replaced the vertical IC (TDA8170) and all the components (excep
Phillips question!	18 Mar 2005 02:15 GMT	1
M # PL0127 C121, RF connector was broken off, & metal plate has shorted components by the tuner! All repaired, now vertical has lines throughout the whole picture! Tried another vertical IC, still the
Sound card noise	18 Mar 2005 01:39 GMT	5
Hi, when I record with windvr on my computer, picture is good, but I hear a grounding (buzzing problem) noise, the 3.5mm plug going in to the sound card is good, never had noise before, what could cause this?
Online Service Manuals	18 Mar 2005 01:19 GMT	1
Does anyone know of a good source for online service manuals? Especially for units made within the last five years. Doesn't have to be a free site either. Thanks.
Help - JBL PSW-D115 problem	18 Mar 2005 00:53 GMT	1
I have a JBL PSW-D115 sub, when I turn it on there is a VERY loud thump/noise. I assume it continues when the sub is left on, but I have only turned it off immediately after turning it on. Any ideas on what the problem could be?
tv audio not clear	18 Mar 2005 00:37 GMT	6
what has happened to cause this? sometimes it becomes garbled. have a nice day
oscilloscope problems	17 Mar 2005 23:24 GMT	5
Hello everyone, My oscilloscope has gone wrong. Was going fine then it suddenly went out of focus for no reason. The focus knob hardly has an effect, its majorly out of focus any ideas ?
:: :: :: :: post 1013 - DO YOU WANT TO KNOW FOR SURE YOU ARE GOING TO HEAVEN? :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: :: ::	17 Mar 2005 23:17 GMT	1
http://www.want-to-be-sure.blogspot.com << Click On Link
GE 46GW947 keep changing channels	17 Mar 2005 21:07 GMT	3
Please help me!!! I have GE 46GW947 projection TV and when it is turned on, it keep changing channels suddenly. Sometimes, it is not turned on at all, but, after a while, I can turn
1 amp fuse in my Emerson VCR is burning and getting open	17 Mar 2005 18:04 GMT	3
Jesus Help me how many times the 1 amp fuse in my Emerson VCR is burning and getting open. Some forums say check regulator q603.
RCA question!	17 Mar 2005 15:53 GMT	4
M # 31GT660 CTC187CN3 horizontal output was blown, changed it, & 47 uf cap, & output gets quite hot! Was worked on elswhere! What's the right horiz output? 2SD1885, BUH517, or
Proximity switch/sensor testing?	17 Mar 2005 15:51 GMT	3
New to the group, so apologies if this question has been asked before. My car is fitted with a sensor that tells the ECU that manages the auto gearbox what RPM's the engine is running at. The error code on the car points to the sensor not sending the RPM's to the
Tektronix 2465 dot problem continuation	17 Mar 2005 13:20 GMT	5
I first posted this problem at the end of another post, subject: tektronix 2465a delayed sweep time problem and tekman said that he had the same problem, and had to adjust the grid bias as well as all other hv adjustments. I haven't tired this
Rewiring a ballast. Help needed.	17 Mar 2005 12:46 GMT	61
Hello, I am having some trouble rewiring a ballast. It's an older one that my wife has above her fish tank. The On/Off switch is flaky (it works about 30% of the time) so she wants to set it up on a timer to go on and off for her fish.