Home | Contact Us | FAQ | Search & Site Map | Link to Us
Sign In | Join | Other 45 Sites in Network
Home
Discussion GroupsElectronicsBasicsRepairDesignCADComponentsEquipmentElectrical Engineering
ElectronicsKB.com
Contact UsLink To UsSearch & Site Map

Electronics Forum / Repair / August 2004



Tip: Looking for answers? Try searching our database.

ThreadLast Post  Replies
Pin out for LA4100 7pin DIP 1 Watt Amp.19 Aug 2004 20:41 GMT3
I am working on a multiband portable radio, The BandLeader by Randix,
Model No. MB 5552.  One of the wires going to the speaker has broken
off the PCB.  The other wire goes to a LA4100 chip.  I did a google
through 10 pages of matches and found out the LA4100 is a 1 Watt audio
Proton 32019 Aug 2004 18:45 GMT2
I am searching for a schematic, or alternatively information on a
replacement tuner lamp, for a Proton 320 clock radio. I'd appreciate any
information very much as I have it apart on a table and can't go any
farther. Thanks in advance.
Arnaud la trad dans ta bal. (NL)19 Aug 2004 17:12 GMT1
Voilà :-)
Signature

*Alain Beguin*
http://www.zoo-logique.org/mesnews/index-nl.php

KOSS parts19 Aug 2004 15:37 GMT9
My KOSS KS2503 Home Theatre died while watching a movie.  I replaced the
fuse and it blew again.  I would like to replace the power supply, but KOSS
won't sell it to me.  Can anyone tell me where I can get KOSS parts?
S: Bimetallic switch data?19 Aug 2004 04:38 GMT4
does anyone know something about the bimetallic switch below:
ELTH
Type 261
16(3)250
Panasonic Camcorder wont read SD Card19 Aug 2004 03:02 GMT1
I have a panasonic camcorder NVGS4 (I think) and on Sunday it refused
to read the SD card. I have been happily taking stills on it for a
couple of years, and have always deleted them when transferred to the
pc, so it isnt full.
Space Invaders Flyback Transformer?19 Aug 2004 02:36 GMT5
Anyone have any of these used, or know if they are making any as
aftermarket? No. On the FBT is: 24D25240B23-185
I cant believe so far no aftermarkets were made up on this classic Arcade
Game! If anyone has a Used working One, send it to me and I will get a bunch
Pioneer PDP-V401e plasma troubles18 Aug 2004 23:02 GMT2
i'm looking for the service manual for a Pioneer PDP-V401e plasma display.
or alternative - a way to repair the Y drive assembly.
the story goes - i had a white band across the bottom 1/4 of the screen.
i sent the display off and found out that an opto-coupler had failed, there
Zen 9-1559 based set (32")18 Aug 2004 23:02 GMT3
Hi all;
Anyone ever run into this ? Set comes in no green, tube is fine. Problem was
the basic 82K resistor but it now has a more interesting symptom, lucky me.
Now when you go to the menus the base greyscale shifts. When you got a blue
thumb drive18 Aug 2004 22:17 GMT1
just out of curiousity. does anybody know what IC does a USB thumb drive
installed with? just came across my mind to upgrade my 64MB to say ....
256MB by swapping the IC inside the thumb drive.
thanks
Owners Manual18 Aug 2004 18:48 GMT1
Need Owners Manual, For Sylvania model SST4272.
Mitsubishi CT-20AM1S Tuner VH faulty??18 Aug 2004 09:19 GMT2
I have a Mitsubishi CT-20AM1S(A), which looses the tune on the VH high band.
Would it be a faulty tuner or a fault on the board. I think this has a AL-5
chassis.
All other bands are fine and it will hold its tune for up to a day then
Tektronix TDS540 Calibration Procedure???18 Aug 2004 07:43 GMT3
I picked up two non-working Tek Scopes a TDS540 and a TDS520.
Previous owner swapped the processor boards, unprotected the
calibration ram and let 'er rip.  Apparently there was all manner
of complaining from the scope before it locked up.
Kenmore microwave 9992118 Aug 2004 03:42 GMT8
This one's for the archives.
My microwave is a Kenmore, model #99921 (564.9998210) with a Sanyo 11355
controller board.  Symptoms were that the light would come on with the door
open, but the only activity out of the display was to show a 0.
Pin out for LA4100 7pin DIP 1 Watt Amp.18 Aug 2004 01:46 GMT2
I am working on a multiband portable radio, The BandLeader by Randix,
Model No. MB 5552.  One of the wires going to the speaker has broken
off the PCB.  The other wire goes to a LA4100 chip.  I did a google
through 10 pages of matches and found out the LA4100 is a 1 Watt audio
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 July, 2004
 
Sign In
Join
My Latest Posts
My Monitored Threads
My Blog
My Photo Gallery
My Profile
My Homepage

Start New Thread



©2009 Advenet LLC   Privacy Policy - Terms of Use
This website includes both content owned or controlled by Advenet as well as content owned or controlled by third parties.